Solve your Litter-Robot 4 red-green light issue with our easy guide. Get quick help for calibration issues. Click for immediate support! ... Litter-Robot 4: Red and green alternating light bar (Calibration issue) ... as well as measure its weight. If the unit displays a red and green alternating light bar, the unit has lost its factory scale ...1. When your cat exits Litter-Robot, a timer counts down, allowing the litter to clump before a clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a sealed waste drawer below. 4.Preparation. If Litter-Robot 4 displays a blue light bar with a blinking blue light adjacent to the Connect button, this indicates that the unit is connecting to the app or has disconnected and is trying to reconnect but has not successfully reconnected.Ensure proper placement. Your Litter-Robot comes fully assembled and ready to use. Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet. Instruction Manual. Toll Free: 877-250-7729. www.Litter-Robot.com. Thank you for purchasing Litter-Robot® Open Air, the self-cleaning litter box that really works! At AutoPetsTM (Automated Pet Care Products, Inc.), we aim to develop products that keep your pets happy and make your life easier. 1. When your cat exits Litter-Robot, a timer counts down, allowing the litter to clump before a clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a sealed waste drawer below. 4. Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale™ will not recognize kittens that weigh less than 3 lbs. Therefore, kittens that weigh less than 3 lbs can use Litter-Robot 4, but not in automatic mode. Litter-Robot 3 is equipped with a main circuit board that controls the robot's functionality. Litter-Robot 3 Connect unit's main circuit board also controls the connectivity of the robot. Within this circuit board are the main processor, WiFi connectivity chip (for connect units), ambient light sensor, as well as main harness connectors for ...How to Install a Waste Drawer Liner | Litter-Robot 3. Watch on. Open a new waste drawer liner or bag. For Litter-Robot 4: Wrap the edges of the waste drawer liner over the rim of the waste drawer. For Litter-Robot 3: Roll down the edges of the waste drawer liner a few times. Push the rolled edges of the liner into each of the four tabs in the ...Oct 25, 2022 ... In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them.Litter-Robot is equipped with anti-pinch sensors on both sides of the waste drawer chute to ensure your cat’s safety while in use. These sensors monitor for potential pinch conditions at all times. If your unit displays a green and white alternating light bar, this indicates an anti-pinch fault during power up.Litter-Robot will switch back to household power when it returns, and the unit will begin recharging the battery. 1. Press the Power button to turn the unit off, then unplug the unit. 2. Remove the Bonnet and Globe. 3. Locate the unit serial number. It can be found on the inside back wall of the base, behind the waste drawer, or on the exterior ...This manual will help you get the most out of your Litter-Robot. We will guide you through the setup process, as well as provide you with useful tips and advice for acclimating your …These sensors detect when a cat has entered or exited the unit. If the unit detects an issue with all three laser sensors, called curtain sensors, it will indicate a fault with the entire system and the light bar on the Litter-Robot will display red and blue alternating lights. You will also receive a notification on your phone if you use the ...Indices Commodities Currencies StocksMar 14, 2024 ... Are all of your Litter-Robot 3's lights flashing at the same time? Maybe you received a “Litter-Robot has a home or dump position fault” ...Remove any fence that is attached to the Litter-Robot bezel. Notice the two “notches” on the lower inside edge of the bezel. Set the shield hinge onto the bezel using the notches as a guide to center the hinge. Using your thumb and forefingers, hold one end of the shield hinge against the bezel. Press down until you hear a click, then ...Litter Box Storage Cabinet: Assembly Guide & Manual. Place your Litter-Robot 4 in any room of the house with no one the wiser! The Storage Cabinet hides your automatic litter box (which your cat can access through the interchangeable open side entry), while the Hutch doubles as a cat tree and shelf space.Replacing the Litter-Robot 4 Globe is easy. Follow these steps to remove the old globe and quickly install a new one. Make sure the unit is in the Home/Ready position. Press the Power button to turn the unit off, then unplug the unit. Remove the fence from the bezel at the globe entrance (if installed). Open the bonnet: Press and hold the ... 1. When your cat exits Litter-Robot, a timer counts down, allowing the litter to clump before a clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a sealed waste drawer below. 4. Litter-Robot 4: White blinking middle light (Over-the-air "OTA" update) Whisker has the ability to provide updated firmware to your robot with fixes to correct known issues with the unit. We recommend that you always keep your Litter-Robot’s firmware updated to ensure the best possible operation.Litter-Robot 4: Assembly and disassembly. Litter-Robot is built in a modular way to make troubleshooting and maintenance simple. We’ll show you how to disassemble your unit to access certain areas for ongoing maintenance. Litter-Robot 4 has five main components: the base, the bezel, the globe, the waste drawer, and the bonnet.Litter-Robot 4 vs. Litter-Robot 3 Litter-Robot 4. Pro: Suitable for up to 4 cats; Pro: Cat detection sensor prevents cleaning cycle with a cat inside; Pro: Customize the cycle timer; Pro: Advanced odor control; Pro: Much quieter when cycling—almost unnoticeable; Pro: More data tracking available in the app; Pro: Spacious interior; Pro: Wide ...Use clumping litter or litter beads and crystals that are small enough to pass through the screen. Add litter until it meets the raised MAX fill line when spreadPower. Plug the small end of the power supply into the power input on the back of the base. Plug the AC/DC adapter into a wall outlet. Press the Power buton on the control panel. The Liter-Robot will now perform an initial clean cycle. Note: During initial clean cycle, the cat sensor weight scale is disabled to ensure proper calibration.1. When your cat exits Litter-Robot, a timer counts down, allowing the litter to clump before a clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a sealed waste drawer below. 4.Litter Box Storage Cabinet: Assembly Guide & Manual. Place your Litter-Robot 4 in any room of the house with no one the wiser! The Storage Cabinet hides your automatic litter box (which your cat can access through the interchangeable open side entry), while the Hutch doubles as a cat tree and shelf space.These sensors detect when a cat has entered or exited the unit. If the unit detects an issue with all three laser sensors, called curtain sensors, it will indicate a fault with the entire system and the light bar on the Litter-Robot will display red and blue alternating lights. You will also receive a notification on your phone if you use the ...Litter-Robot will switch back to household power when it returns, and the unit will begin recharging the battery. 1. Press the Power button to turn the unit off, then unplug the unit. 2. Remove the Bonnet and Globe. 3. Locate the unit serial number. It can be found on the inside back wall of the base, behind the waste drawer, or on the exterior ...Discover the best robotics engineering company in Estonia. Browse our rankings to partner with award-winning experts that will bring your vision to life. Development Most Popular E...Get $25 off the Litter Robot 4 https://bit.ly/LitterRobot_4 In the this video we set the Litter Robot 4 up and have a look at some of the basic features. ...more.Robots are used for a variety of purposes, including welding, handling chemicals, marine exploration and space missions. Advanced robots are designed to serve and assist people. Th...People need robots for dangerous, repetitive and high-precision work. Robots perform tasks in hostile environments that are impossible for humans, while also carrying out repetitio...Litter-Robot 4: Light Codes Guide Litter-Robot 4: Night Light Feature Litter-Robot 4: Night Light Not Coming On or Shutting OffSet the key insert into the key as shown. Hold the plug in place while you insert the screw through the key from the other side. From the outside of the globe, rotate the key into the pocket of the base. With a Phillips-head screwdriver, use the screw from your plug kit to fasten the key to the plug. Confirm that the globe is positioned correctly.Jan 23, 2024 ... The Litter-Robot is equipped with an Anti-Pinch Safety Feature to make the Litter-Robot extra safe for your cat.Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. ... Follow the steps in our Litter-Robot 4: Laser board installation guide to ensure the laser board is securely connected. You will need: Phillips-head screwdriver; Successful: If your ...Each day, robotics and artificial intelligence are revolutionizing how we live, work, and play in the modern world. If you’re an investor, then you may be looking to ride the waves...The Litter-Robot 3 Backup Battery provides up to 48 hours of operation if power is interrupted. When power is interrupted, the unit will automatically switch to battery power and a yellow light will illuminate the Power button on the Control Panel. To conserve energy, the night light will not function.Troubleshooting. Follow the steps in our Litter-Robot 4: Motor Installation Guide to ensure the motor is securely connected. You will need: Phillips-head screwdriver. Successful: If your Litter-Robot displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a blue and white alternating light bar, there's likely an ... Sleep Mode is useful for units located in bedrooms or areas where you may not want the Litter-Robot to cycle for a certain period of the day. A 3-second long press of the Cycle button will enable Sleep Mode. The Light Bar will change from blue to purple, indicating that Sleep Mode is active. The unit is programmed with a default 8-hour sleep ... Learn how to install Litter-Robot 4 Fence with our Fence Installation Guide or Mini Fence Installation Guide. Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Get started with your Litter-Robot 4 with ease. Visit our quick start guide for step-by-step instructions. Blue: WiFi is connected, and the unit is ready for the next use. White: WiFi is turned off. Blinking Blue: WiFi is disconnected / reconnecting. Learn more. Blinking Yellow: Unit is in Onboarding Mode. Follow the prompts in the app and scan the QR code on the back of the unit as directed. Press the Connect button to exit Onboarding Mode.Ensure proper placement. Your Litter-Robot comes fully assembled and ready to use. Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet.Discover the best robotics engineering company in Estonia. Browse our rankings to partner with award-winning experts that will bring your vision to life. Development Most Popular E...There are few things better than sitting down to a clean house and knowing that you didn’t have to do much of the work. While a robotic vacuum can’t quite do the dishes for you, it...Open the filter cover and remove the carbon filter (if installed). Place 2 OdorTrap® Packs under the filter cover and reinstall the cover. Under normal use, 2 packs should last approximately 1 month. (Note: OdorTrap® Packs may shift as the globe rotates.) Close the bonnet: Rotate the bonnet downward over the globe and push down on the bonnet ...Litter-Robot 3 Connect unit's main circuit board also controls the connectivity of the robot. Within this circuit board are the main processor, WiFi connectivity chip (for connect units), ambient light sensor, as well as main harness connectors for power and other peripheral sensors or systems. Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more. Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more.The Litter-Robot 3 Backup Battery provides up to 48 hours of operation if power is interrupted. When power is interrupted, the unit will automatically switch to battery power and a yellow light will illuminate the Power button on the Control Panel. To conserve energy, the night light will not function. Preparation. Litter-Robot 4 is equipped with features for future accessories to make life for pets and pet parents endlessly better. If your unit’s light bar is alternating blue and purple, this indicates your unit entered a mode for an accessory that is not detected. Litter-Robot 4 Manual. Created by Ken MacCormick, Modified on Sat, 09 Sep 2023 at 01:10 PM by Ken MacCormick. Litter-Robot 4 Owners Manual. Downlaod PDF.Litter-Robot 4. Pro: Suitable for up to 4 cats. Pro: Cat detection sensor prevents cleaning cycle with a cat inside. Pro: Customize the cycle timer. Pro: Advanced odor control. Pro: Much quieter ...Feeder-Robot can be equipped with a backup battery (sold separately) that provides approximately 24 hours of operation in power-saving mode if power is interrupted. Note: When power is interrupted, the unit will automatically switch to battery power and a blinking yellow light will illuminate the power button on the control panel.Once logged in, tap the plus button to add a new robot. Select the Litter-Robot 4 icon to start the onboarding process. Read more about acclimating your cat to Litter-Robot and confirm the Connect light is flashing yellow to continue. Register your robot by scanning the QR code on the back of the unit to link the serial number to your app. Add Litter 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is indoors on a firm, level surface and in a cool, dry location. Must not be touching any walls. Place litter mats or rugs in front of the unit. The Litter-Robot will now perform an initial clean ... Automation robotics has revolutionized the way businesses operate by streamlining processes and reducing costs. One of the key benefits of automation robotics is its ability to sig...Oct 25, 2022 ... In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them.Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale™ will not recognize kittens that weigh less than 3 lbs. Therefore, kittens that weigh less than 3 lbs can use Litter-Robot 4, but not in automatic mode. Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Resolve the 'Accessory not detected' issue on your Litter-Robot 4, indicated by an alternating blue and purple light bar, with our visual troubleshooting guide. Visit our Getting Started page for setup directions, manuals, and video tutorials.. Your Litter-Robot 4 ships fully assembled. Follow these steps to get started or refer to the user manual for more information. How to print the president's head. The photograph above, contrary to appearances, does not show US president Barack Obama being beamed into another dimension by a gang of alien rob... Preparation. Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to ensure your cat is always safe. There are three curtain sensors located in the ... Litter-Robot 4: Blue and white alternating light bar (Motor fault) Litter-Robot comes equipped with current-sensing capability to detect if the motor is connected and running properly. If the unit displays a blue and white alternating light bar, there is an issue with the motor connection, which affects the rotation of the globe.Solve your Litter-Robot 4 red-green light issue with our easy guide. Get quick help for calibration issues. Click for immediate support! ... Litter-Robot 4: Red and green alternating light bar (Calibration issue) ... as well as measure its weight. If the unit displays a red and green alternating light bar, the unit has lost its factory scale ...Watch on. 1. Remove the bonnet and globe from your existing Litter-Robot 3. 2. Place the globe on the new base, making sure it's straight and in the tracks. 3. Place the bonnet on the new base by inserting the bonnet tabs into the rear bonnet slots, then press the latches while rotating it forward, until the latches click into place. 4.Page 31 Cleaning the Globe Press the Empty button to cycle the Globe clockwise, which will allow the litter to fall through the Waste Port and into the Waste Drawer for easy disposal. Sweep any leftover litter toward the Waste Port. Then, press either Cycle or Reset to return the Globe to the Home position.Watch on. The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your ...In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...Needle-nose pliers. Flathead screwdriver. Press the Power button to turn the Litter-Robot off and unplug it from the wall. Remove the power supply plug from the rear of the unit. Remove the bonnet and globe. Carefully remove the old blue applique using a small flathead screwdriver or blade. Apply the new black applique to the control panel cover.This manual will help you get the most out of your Litter-Robot. We will guide you through the setup process, as well as provide you with useful tips and advice for acclimating your … Add Litter 1 3 2 4 If possible, place the Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is indoors on a firm, level surface and in a cool, dry location. Must not be touching any walls. Place litter mats or rugs in front of the unit. The Litter-Robot will now perform an initial clean ... Reinstall the fence by snapping it onto the bezel at the globe entrance. Plug the unit in and power it on. The Litter-Robot will then perform a clean cycle and return to the Home position with the blue light on. Successful: After your Litter-Robot cycles, it should return to the Home position, displaying a blue light bar.In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...Watch on. 1. Remove the bonnet and globe from your existing Litter-Robot 3. 2. Place the globe on the new base, making sure it's straight and in the tracks. 3. Place the bonnet on the new base by inserting the bonnet tabs into the rear bonnet slots, then press the latches while rotating it forward, until the latches click into place. 4.Litter-Robot 3: Yellow flashing slowly (Cat sensor) The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second. This will also occur if the cat sensor is activated by a cat ... Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale™ will not recognize kittens that weigh less than 3 lbs. Therefore, kittens that weigh less than 3 lbs can use Litter-Robot 4, but not in automatic mode. Simply place OdorTrap™ Packs in your Litter-Robot 4 filter pocket (see installation guide) or Litter-Robot 3 waste drawer near the carbon filter. We recommend replacing one pack every two weeks or two packs every month. 4. Keep it clean! Once every month or so (depending on how frequently the unit is used), give your Litter-Robot a …Have robots changed manufacturing in a significant way, or do we still largely rely on man power? Find out how robots changed manufacturing. Advertisement Break things down to the ... The light not only adds to the aesthetic of your Litter-Robot, it will also provide additional light to those cats that need it. The Litter-Robot arrives with the Automatic Night Light function enabled. You can set the light to always on, off, or automatic. You can also adjust the brightness of the night light. How to Change the Night Light Setting The bonnet functions as a cover and guard for the waste port as the globe rotates. The globe will not rotate without the bonnet installed. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second.Mar 6, 2017 ... http://www.litter-robot.com/ We want your cats to love their Litter-Robot. This is why we have thought of unique Litter-Robot features that ...The logistics industry is undergoing a significant transformation, driven by technological advancements such as automation and robotics. One of the most notable trends in the logis... Visit our Getting Started page for setup directions, manuals, and video tutorials.. Your Litter-Robot 4 ships fully assembled. Follow these steps to get started or refer to the user manual for more information. Feeder-Robot can be equipped with a backup battery (sold separately) that provides approximately 24 hours of operation in power-saving mode if power is interrupted. Note: When power is interrupted, the unit will automatically switch to battery power and a blinking yellow light will illuminate the power button on the control panel.The Litter-Robot arrives with the automatic night light function enabled. You can set the light to always on, off, or automatic as well as adjust the brightness of the night light. When the light sensor, located in the control panel, detects low-light conditions, the night light turns on automatically. How to activate. A 3-second long press of ...Make sure your mobile device's bluetooth is enabled. To start the onboarding process, put the Litter-Robot into setup mode. Press and hold the Connect button on the control panel for three seconds. The control panel will turn solid blue with a yellow light on the bottom. Next, open up the Whisker app.The logistics industry is undergoing a significant transformation, driven by technological advancements such as automation and robotics. One of the most notable trends in the logis...Troubleshooting. Follow the steps in our Litter-Robot 4: Motor Installation Guide to ensure the motor is securely connected. You will need: Phillips-head screwdriver. Successful: If your Litter-Robot displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a blue and white alternating light bar, there's likely an ...The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...Considering we've received a huge response on our Litter-Robot II Basic Troubleshooting Guide, we've decided to help our customers further by creating this advanced troubleshooting guide. This guide will help you with opening up the Litter-Robot II to verifying connections of the motor and circuit board. Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale™ will not recognize kittens that weigh less than 3 lbs. Therefore, kittens that weigh less than 3 lbs can use Litter-Robot 4, but not in automatic mode. If you’re a cat owner, you know how important it is to find the right litter for your furry friend. With so many options available on the market, it can be overwhelming to decide w...The following are the typical causes of why your Litter-Robot is having torque issues: 1. Motor Obstruction. The globe of the Litter-Robot can get jammed at one point while using the litter box. This causes the motor to stop and will display yellow and red lights blinking in sequence. Recommended: How to fix yellow light flashing in Litter ...Blue: WiFi is connected, and the unit is ready for the next use. White: WiFi is turned off. Blinking Blue: WiFi is disconnected / reconnecting. Learn more. Blinking Yellow: Unit is in Onboarding Mode. Follow the prompts in the app and scan the QR code on the back of the unit as directed. Press the Connect button to exit Onboarding Mode.Learn how to easily remove the internal shield, install the key and plug, and confirm proper functionality. If your Litter-Robot 3 predates February 2018, removing the internal shield is crucial to prevent the '3 lights flashing' fault. The Litter-Robot 4 Backup Battery ensures you don't have to scoop in the event of a power ou
Litter-Robot 4: Blue and white alternating light bar (Motor fault) Litter-Robot comes equipped with current-sensing capability to detect if the motor is connected and running properly. If the unit displays a blue and white alternating light bar, there is an issue with the motor connection, which affects the rotation of the globe.Simply put: A well-functioning Litter-Robot means a happier cat and, by extension, a happier you. 1. The most common issues with Litter-Robot not cycling stem from power issues, the type of litter used, foreign objects, or software malfunctions. 2. Regular maintenance, including weekly waste drawer checks and bi-weekly thorough …Troubleshooting. Follow the steps in our Litter-Robot 4: Motor Installation Guide to ensure the motor is securely connected. You will need: Phillips-head screwdriver. Successful: If your Litter-Robot displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a blue and white alternating light bar, there's likely an ...Replacing the Litter-Robot 4 Globe is easy. Follow these steps to remove the old globe and quickly install a new one. Make sure the unit is in the Home/Ready position. Press the Power button to turn the unit off, then unplug the unit. Remove the fence from the bezel at the globe entrance (if installed). Open the bonnet: Press and hold the ... Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more. Feeder-Robot can be equipped with a backup battery (sold separately) that provides approximately 24 hours of operation in power-saving mode if power is interrupted. Note: When power is interrupted, the unit will automatically switch to battery power and a blinking yellow light will illuminate the power button on the control panel.Set aside the filter cover. Remove the carbon filter (if installed) and prepare to install the OdorTrap® Holder. Open the OdorTrap® Holder by unsnapping the two (2) side clips. Place the opened OdorTrap® Holder on the filter cover. The center arrow on the OdorTrap® Holder must line up with the small dot on the center of the filter cover.Watch on. If your unit displays a yellow light bar, this indicates that the unit has been "paused". Pressing the Cycle or Reset button should get it to resume cycling. If it does not, please power the unit off and back on using the Power button. If your unit displays a blue light bar, you've been successful. If your unit is still displaying a ...Remove the two screws holding the backup battery bracket in place. Set the bracket to the side. Unplug the red and black wires from the battery at the quick disconnects. Set the battery aside. Remove the 9 screws from the bottom of the base. Flip the base back upright and gently remove the top part of the base. If your unit displays a green and white alternating light bar, this indicates an anti-pinch fault during power up. First, let’s check inside the waste drawer to see if there are any foreign objects that could be activating the sensors. Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a Clean ... Litter-Robot Premium Litter All Natural Sun-dried Clay. Non Tracking, 99% Dust Free. Price: $29.95 (Free Shipping) Drawer Liners (100 pk) Biodegradable bags for your Litter-Robot. Price: $39.99 (Free Shipping) Carbon Filters (3 pk) Replacement waste drawer carbon filters. Price: $18.99 (Free Shipping) Order these accessories and more at www ...Visit our Getting Started page for setup directions, manuals, and video tutorials.. Your Litter-Robot 4 ships fully assembled. Follow these steps to get started or refer to the user manual for more information.Litter-Robot 4: White Blinking Middle Light (Over-The-Air "OTA" Update) Whisker has the ability to provide updated firmware to your robot with fixes to correct known issues with the unit. We recommend that you always keep your Litter-Robot’s firmware updated to ensure the best possible operation.Litter-Robot 3 is equipped with a main circuit board that controls the robot's functionality. Litter-Robot 3 Connect unit's main circuit board also controls the connectivity of the robot. Within this circuit board are the main processor, WiFi connectivity chip (for connect units), ambient light sensor, as well as main harness connectors for ...Litter-Robot 4 ships with a waste drawer liner installed. These liners are made specifically for any Litter-Robot model, but an 8-13 gallon (30-49L) trash bag will also work. Clear bags work best. Installing the waste drawer liner. To install a new waste drawer liner, you’ll need to remove the drawer from Litter-Robot.Blue: WiFi is connected, and the unit is ready for the next use. White: WiFi is turned off. Blinking Blue: WiFi is disconnected / reconnecting. Learn more. Blinking Yellow: Unit is in Onboarding Mode. Follow the prompts in the app and scan the QR code on the back of the unit as directed. Press the Connect button to exit Onboarding Mode.These sensors detect when a cat has entered or exited the unit. If the unit detects an issue with all three laser sensors, called curtain sensors, it will indicate a fault with the entire system and the light bar on the Litter-Robot will display red and blue alternating lights. You will also receive a notification on your phone if you use the ... Visit our Getting Started page for setup directions, manuals, and video tutorials.. Your Litter-Robot 4 ships fully assembled. Follow these steps to get started or refer to the user manual for more information. Automatic Night Light. Guide elderly cats during night time visits with Litter-Robot 3’s built-in night light. Sleep Mode. Pause automatic cycling in 8-hour increments. Adjustable Cycle Timer. Choose a 3, 7, or 15 minute delay before cycling begins. Control Panel Lockout.View and Download whisker Litter-Robot 4 instruction manual online. Litter-Robot 4 pet care product pdf manual download.Robots are made of three main components: the controller, mechanical parts and sensors. The type of materials that make up the different components will vary depending on the type ... How to Install a Waste Drawer Liner | Litter-Robot 3. Watch on. Open a new waste drawer liner or bag. For Litter-Robot 4: Wrap the edges of the waste drawer liner over the rim of the waste drawer. For Litter-Robot 3: Roll down the edges of the waste drawer liner a few times. Push the rolled edges of the liner into each of the four tabs in the ... Litter-Robot 3 is equipped with a main circuit board that controls the robot's functionality. Litter-Robot 3 Connect unit's main circuit board also controls the connectivity of the robot. Within this circuit board are the main processor, WiFi connectivity chip (for connect units), ambient light sensor, as well as main harness connectors for ...Watch on. If your unit displays a yellow light bar, this indicates that the unit has been "paused". Pressing the Cycle or Reset button should get it to resume cycling. If it does not, please power the unit off and back on using the Power button. If your unit displays a blue light bar, you've been successful. If your unit is still displaying a ...A solide carmine light turn your Litter-Robot 3 remote panel average that the cat sensor was active by your cat type of globe while the unit was available fork ...If your Litter-Robot is not detecting your cat or not cycling, complete the troubleshooting steps in our Litter-Robot 3: Cat not detected guide.. If your Litter-Robot is slowly flashing yellow or stuck upside down due to the cat sensor, complete the troubleshooting steps in our Litter-Robot 3: Yellow light flashing (Cat sensor) guide.. If your Litter-Robot is … Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Chat with us 1-877-250-7729 Submit a ticket. Find answers, guides, & solutions for your Litter-Robot. Your first stop for answers and solutions to your Litter-Robot questions. In today’s fast-paced world, businesses are constantly seeking ways to streamline their operations and improve efficiency. One technology that has gained significant attention is r...Oct 7, 2023 ... Yellow “Ping Pong” Light Bar Flashing: Whoops, the anti-pinch safety feature has been activated. Solid Red Light Bar: The sensors detected a cat ... The Litter-Robot 4 Backup Battery ensures you don't have to scoop in the event of a power outage. It provides 24-48 hours of use when power is interrupted. WiFi and night light functionality will be disabled during backup battery mode to conserve energy. Light bar display intensity will be reduced by 50%. Tools Needed: Phillips-head screwdriver. 1. Needle-nose pliers. Flathead screwdriver. Press the Power button to turn the Litter-Robot off and unplug it from the wall. Remove the power supply plug from the rear of the unit. Remove the bonnet and globe. Carefully remove the old blue applique using a small flathead screwdriver or blade. Apply the new black applique to the control panel cover.Robot vacuums have revolutionized the way we clean our homes, making it easier and more convenient than ever. However, just like any other electronic device, they can sometimes exp...Also read: Decoding the Litter Robot 4 Cat Sensor Fault. Understanding the Litter-Robot 4 Light Indicators: Yellow Solid: Meaning: This indicates that the Litter-Robot unit is in a “paused” state. Solution: Resume its cycle by pressing the Cycle or Reset button. If unsuccessful, try turning the unit off and on using the Power button. Yellow ...Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Chat with us 1-877-250-7729 Submit a ticket. Find answers, guides, & solutions for your Litter-Robot. Your first stop for answers and solutions to your Litter-Robot questions.The first robot was created by the Greek mathematician Archytas of Tarentum. It was a flying wooden dove that traveled up to 200 meters through the air by flapping its wings.Visit our Getting Started page for setup directions, manuals, and video tutorials. Your Litter-Robot 4 ships fully assembled. Follow these steps to get started or refer to the user …You will see a single white light blinking on your unit’s control panel – this is the signal that your robot’s firmware is updating. Our new LR4 (just received 3 weeks ago) was working …Litter-Robot 3: All three lights flashing (Globe position fault) Litter-Robot 3: Blue Light Flashing (Drawer Full) Litter-Robot 3: Buttons and Lights. Litter-Robot 3: Cat not detected. Litter-Robot 3: Cat Sensor Troubleshooting. Litter-Robot 3: Control Panel Lockout. Litter-Robot 3: Cycle delay setting.Introducing your cat to Litter-Robot. Most likely, your cat will quickly adapt to Litter-Robot. When using in automatic mode, be sure your cat or kitten weighs at least 3 lbs—the weight scale will not recognize cats weighing less than 3 lbs. ... Empty the waste drawer when indicated by the app or the flashing blue light on the control panel ...Preparation. Litter-Robot 4 is equipped with features for future accessories to make life for pets and pet parents endlessly better. If your unit’s light bar is alternating blue and purple, this indicates your unit entered a mode for an accessory that is not detected.Keeping your home clean and tidy is essential for a healthy living environment. However, finding the time to vacuum regularly can be a challenge, especially if you have a busy sche...Mar 14, 2024 ... Is your Litter-Robot 3 presenting a yellow light flashing slowly? Maybe you received a “cycle interrupted” or “bonnet removed” notification?Learn how to remove and install the Litter-Robot 4 Step Mat. Pull the waste drawer out of the base by a few inches. Grip the left or right back corner of the step mat and lift. The step mat will pop right out. To reinstall, simply snap the mat back into place. Slide the waste drawer closed and press the Reset button to zero the weight sensors.Litter-Robot 4: Light Codes Guide Litter-Robot 4: Night Light Feature Litter-Robot 4: Night Light Not Coming On or Shutting Off Disassemble and clean Feeder-Robot (refer to our Care & Cleaning guide). With the